Posted 20 hours ago

kenable External CAT5e Outdoor Use COPPER Ethernet Network Cable Reel UTP 100m Black [100 metres]

ZTS2023's avatar
Shared by
Joined in 2023

About this deal

We recommend to use faceplates with full copper cables as oppose to crimping them for our plates see the QS numbers below: Cat5 and Cat5e are two common classifications of Ethernet or network cabling. The Cat5e specification came into widespread use after 2001, before which Cat5 had been the latest standard.

The best way to tell the difference is on the sheath of the cable. The cable marking will have code numbers and other digits. However, it will also note if the cable is Cat5e or Cat6. In addition, the Cat6 cable will have a plastic central divider between the four pairs. Cat5e will not have this. However, this is dependent on different manufacturers, so not always 100% the case. Do Cat6 cables work with Cat5? Cat5e is capable of upto gigabit networking speeds (this is dependent on your network). Our cat5e cables are flexible and easy to install.Cat5 was the original new category in the data cabling index. However, since 2001, Cat5e has been the standard. Cat5 was limited to 100Mb transmission. Cat5e was implemented to achieve 1 Gigabit Ethernet. Cat5 is no longer manufactured and is rarely seen, even in older buildings. You can use a CAT6 cable instead of a CAT5e cable in almost all situations. However, there are unusual cases where it is only sometimes valid. In a laboratory installation, we installed Cat5e cabling as the central plastic divider within Cat6 cables would have let pathogens escape the contained areas by travelling along the plastic core. The basis of structured cabling is that there is a standard data cabling specification that applies to all technology. Therefore, whatever the technology, it will run the same over standardised cabling. Thus, the maximum distance of 90 metres for Cat5e applies to CCTV and Computers, WiFi, Telephones, etc. The 90m allows for 5m patch leads at each end. However, a 100m direct link is also allowed, so this could apply to a direct link to a CCTV camera. Can I run HDMI over Cat5?

UTP stands for unshielded twisted pair, and FTP is Foil Twisted Pair. Therefore, FTP is similar to a standard UTP cable with a foil shield surrounding the inner cores. Thus, the shielding provides additional protection from external noise inference.

Cat5e cable has a maximum bandwidth frequency of 100 MHz. Megahertz are the rate at which a signal can change states. In data cabling networking, this is the change from 1 to 0 or 0 to 1 Will Cat5e do Gigabit Ethernet speeds? U/UTP is, therefore, the most susceptible to interference, signal noise, return loss, and attenuation, although the cable will be considerably cheaper to buy. F/FTP will offer the greatest protection against performance-limiting factors like crosstalk, but it will also be the most expensive type to buy. Stranded conductor (stranded core) Cat5/Cat5e Ethernet cable tends to be used for establishing shorter runs between temporary or easily movable wired networks. Small office networks, such as those linking computers to a router via a short Cat5e patch cable or similar will generally be fine using stranded Ethernet wiring. Most standard Ethernet patch cables at lengths of 50 feet or less will tend to have stranded conductors.

Cat5 cable specifications dictate it should be able to handle data transfer over Ethernet networks at frequencies (also known as bandwidth, or data-carrying capacity) of up to 100 MHz. Cat5e offers superior performance and is rated for frequencies of up to 350 MHz. This is due in part to its stricter performance requirements for things like crosstalk (interference between individual wires), attenuation and return loss. Our kenable outdoor networking cable has FULL COPPER 24AWG twisted pairs and can be used indoor as well as outdoor. Its ideal for long or short runs and is UV resistant thanks to its PE sheath ensuring it wont erode over time like standard networking cables. Our Cat5e cables are also waterproof and can even be buried underground! See to the right for a Cat5e cable diagram, showing the basic construction of different types of Cat5e Ethernet cables.However, there are valid use cases for choosing longer runs of Cat5e wiring, in which case you can easily buy reels in lengths of 1000ft or more. Common pre-cut lengths you will see on sale at UK suppliers include 30cm/300mm, 50cm/500mm, 1m, 2m, 3m, 5m, 10m, 30m, 100m, 152m, and 305m. The standard assembly for basic Cat5 cable is often U/UTP, while many high-quality Cat5e Ethernet cables are manufactured with at least some form of additional shielding built-in. This shielding helps to protect the carried signal from several forms of interference, minimising the risk of data corruption or network connection loss. Cat6 is the advanced category of data cable to Cat5e. The main difference between Cat5 and Cat6 is that Cat6 has a bandwidth of 250Mhz, two and a half times the capacity of Cat5e cabling. However, at the standardised 90m permanent link distance, they can only transmit 1 Gigabit Ethernet speeds. However, Cat6 is capable of 10 Gigabit Ethernet up to 55m, although this isn’t a standard length for data cabling design considerations. Simply yes, you can. However, you would be using a more expensive connector and only achieving the lesser performance standard. You can also use Cat5e connectors on a Cat6 cable. However, in this case, you lose the performance of the Cat6 cable and only attain the lower standard overall. Can I use Cat6 instead of Cat5?

Solid conductor (solid-core) Cat5/Cat5e Ethernet cable tends to be used where longer runs need to be set up to achieve a more reliable and stable permanent wired network. This is more common in office buildings and other professional setups. Applications that involve running outdoor Cat5 cable, or passing it through sections of wall, will often benefit from the use of solid-core wiring. Cat5e has a maximum capability of 1 Gigabit Ethernet. The older standard of standard Cat5 had a limit of 100Mb transmission. However, this category of cable is not manufactured anymore. In addition, it is rarely seen in old installations, In rare cases, older phone systems may be wired in standard Cat5 and would not be suitable for Gigabit ethernet. Can Cat5e support 10 Gigabit Ethernet? Cat5 cable is designed to carry data over a wired network connection at speeds of 10 Mbps (Ethernet) or 100 Mbps (Fast Ethernet). You will often see this written as 10/100 Ethernet when shopping for Cat5 cable online. This means that if your local network or incoming internet connection runs at between 10-100 Mbps (also known as a 100BASE-T network), Cat5 Ethernet cable should be able to handle the required data throughput at full speed, with no loss or delay.In addition to the basic Ethernet cable standards and the stranded vs. solid designs, there are also other manufacturing specifications available for each type and category. These are commonly abbreviated as: Further information on this Cat5e cable FAQ can be found here in this article Can you use Cat6 connectors on Cat5e cable? Cat5 and Cat5e cables are available in a wide variety of different lengths. In most cases, Cat5 patch cables tend to be chosen for reasonably short runs (100ft or less), especially if they are stranded core wires. As in all cases of structured cabling installation, the overall price will depend on many factors. These can include the building type, ease of access, number of outlets, the location of the building and the programme of work, among many others.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment